View SP10Q002T_709084.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

record of revision date sheet no. summary kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2702-sp10q002-t-1 page 2-1/1 sh. no.
3. mechanical data (1 ) part name sp10q002-t (2 ) module size 120.0(w)mm * 80.0(h)mm * 7.0(d)mm (3 ) effective display area 88.1 min * 60.0 min. (4 ) dot size 0.335(w)mm * 0.335(h)mm (5 ) dot pitch 0.35 (w)mm * 0.35(h)mm (6 ) number of dots 240 (w) * 160 (h)dots (7 ) duty 1/160 (8 ) lcd film type black/white (negative type) the upper polarizer is glare type.(hardness:3h) the bottom polarizer is transflective type. (9 ) viewing direction 6 o ?clock (10 ) back light cold cathode fluorescent lamp (11 ) weight (80g) kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2703-sp10q002-t-1 page 3-1/1 sh. no.
4. absolute maximum ratings 4.1 electrical absolute maximum ratings. vss=0v:standard item symbol min. max. unit comment power supply for logic vdd-vss 0 6.5 v power supply for lc drive vdd-vee 0 27.5 v input voltage vi -0.3 vdd+0.3 v note 1 input current ii 0 1 a static electricity - - 100 - note 2 note 1 :disp.off,frame,load,cp,d0~d3. note 2 :.make certains you are grounded when handling lcm. 4.2 environmental absolute maximum ratings. i t e m operating storage comment min. max. min. max. ambient temperature 0 c note6 40 c -20 c 60 c note 2,3 humidity note 1 note 1 without condensation vibration - 2.45m/s 2 (0.25g) - 11.76m/s 2 (1.2g) note 5 note 4 shock - 29.4m/s 2 (3g) - 490.0m/s 2 (50g) xyz directions note 5 corrosive gas not acceptable not acceptable note 1 : ta<=40 c:85%rh max. ta>40 c :absolute humidity must be lower than the humidity of 85%rh at 40 c. note 2 : ta at -20 c <48hrs,at 60 c <168hrs. note 3 :background color changes slightly depending on ambient temperature. this phenomenon is reversible. note 4 :5hz~100hz (except resonance frequency,x.y.z each direction within 1 hour). note 5 :this module should be operated normally after finish the test. note 6 :higher starting voltage of cfl and higher lcd driving voltage are needed while operating at 0 c. the life time of cfl will be reduced while operating at 0 c. need to make sure of value of il and characteristics of inverter. also the response time at 0 c will be slower. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2704-sp10q002-t-1 page 4-1/1 sh. no.
5. electrical characteristics 5.1 electrical characteristics i t e m symbol condition min. typ. max. unit 4.75 5.0 5.25 power supply voltage for logic vdd-vss - 3.0 3.3 3.6 v power supply voltage for lc driving vee-vss - -23.1 -22.0 -20.9 v input voltage h level 0.8vdd - vdd v note 1 vi l level 0 - 0.2vdd v power supply current for logic note 2 idd note 2 - 1.9 - ma power supply current for lc driving note 2 iee note 2 - 1.5 - ma recommended ta= 0 c , f =0 - (24.4) - v lc driving voltage vdd-vee ta=25 c , f =0 - (23.5) - v note 3 ta=40 c , f =0 - (22.2) - v frame frequency note4 fframe - 70 75 140 hz note 1 :disp.off,frame,load,cp,d0~d3. note 2 :fframe=75hz,test pattern is all ?q? vdd-vee=(23.5 )v,ta=25 c note 3 :recommended lc driving voltage fluctuate about 1.0v by each module. test pattern is all ?q? . note 4 :need to make sure of flicking and rippling of display when setting the frame frequency in your set. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2705-sp10q002-t-1 page 5-1/2 sh. no.
5.2 electrical characteristics of backlight i t e m symbol min. typ. max. unit unit lamp voltage vl - 300 - v ta=25 c frequency fl 30 70 85 khz ta=25 c lamp current il 4 4.5 5 ma ta=25 c starting discharge voltage vs note 2 (1000) - - v ta=25 c note 1 :please certainly inform hitachi before designing lamp drive circuit according to the above specifications. note 2 :staring discharge voltage is increased when lcm is operating at lower temperature. please check the characteristics of inverter before appling to your set. note 3 :average life time of cfl will be decreased when lcm is operating at lower temperature. note 4 :under lower driving frequency of the inverter , a certain backlight (from cfl & cfl reflection sheet) may generate sound noise. before disigning the inverter , please consider driving frequency and check sound noise from the backlight system note 5 :cfl life time. mtbf= about 20k hours at 25 c icfl=4.5 ma. please note that mtbf is not a guaranteed value. this is a target value for lcm design. note 6 :recommend inverter is invc445(12v) and invc473(5v). kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2705-sp10q002-t-1 page 5-2/2 sh. no.
6. optical characteristics 6.1 optical characteristics ta=25 c (backlight on) item symbol condition min. typ. max. unit note viewing angle f 2- f 1 k>=2.0 - 40 - deg 1,2 contrast ratio k f =0 q =0 - (8) - - 3 response time (rise) tr f =0 q =0 - 160 - ms 4 response time (fall) tf f =0 q =0 - 110 - ms 4 (measure condition by hitachi) note 1.definition of q and f note 3.definition of contrast ?k? (normal) note 2.definition of viewing angle f 1 and f 2 . note 4.definition of optical response x y( q =180 ) viewing directi on x? f 2 f 1 y( q =0 ) operating vol ta ge b1 b2 (b1) (di="h") f =10 (b2) (di="l") k 2 .0 contrast rat io k v ie w ing f lcd sens or (bm-7) backl ight l ight source non- selective state 100% 90% 10% tr tf rise t im e fall t im e select iv e s tate non- selective state k= brightness on selected dot (b1) brightness on non-selected dot (b2 ) kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2706-sp10q002-t-1 page 6-1/2 sh. no. (aperture=1 ) (distance=0.4m) f 1 f 2 f f 1<0 < f 2
6.2 optical characteristics of backlight (lcm ,backlight on,ta=25 c) item min. typ. max. unit note brightness (50) (80) - cd/m 2 il=4.5ma note 1,2 rise time - 5 - minute il=4.5ma brightness 80% brightness uniformity - - +/-30 % undermentioned note 1,3 cfl : initial , ta=25 c , vdd-vee=(23.5)v display data should be all ? on ? . note 1 measurement after 10 minutes of cfl operating. note 2 brightness control :100% note 3 measurement of the following 9 places on the display. definition of the brightness tolerance. y=60 y=120 y=180 x=40 x=80 x=120 p1 p4 p7 p2 p3 p5 p6 p8 p9 max brightness or min brightness - average brightness average brightness * 100% ( ) kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2706-sp10q002-t-1 page 6-2/2 sh. no.
7. block diagram x 1 i c 4 i c 3 i c 2 y240 y161 y160 y81 y80 y1 x 8 0 x 1 ,y 1 d3 d2 d1 d0 x 8 1 x 1 6 0 * i c 5 i c 1 v dd v s s v e e d0 ~ d3 f ra m e l oa d dis p of f cp cf l v cf l gnd ( cf l ) l c d 24 0 * 160 d ot s * t im ing circuit s x 1 ,y 2 x 1 ,y 3 x 1 ,y 4 1 p ow e r s up p l y kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2707-sp10q002-t-1 page 7-1/1 sh. no.
8. interface timing chart 8.1 timing chart 44.64 m s<=t<=8 9. 29 m s load cp x160 x1 x2 d3 y1 y5 y237 d2 d1 d0 y2 y3 y4 y6 y7 y8 y238 y239 y240 f ra me x159 x160 x1 x2 load f ra m e d0~d3 160*t kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2708-sp10q002-t-1 page 8-1/3 sh. no.
8.2 timing characteristics 0 c<=ta<=40 c vdd=5v5% item symbol min. typ. max. unit clock frequency fcp - - 6.5 mhz clock pulse width tw 63 - - ns clock rise,fall time tr,tf - - 20 ns data set up time tdsu 50 - - ns data hold time tdhd 50 - - ns load set up time tlsu 80 - - ns load ? clock time tlc 80 - - ns ?frame? set up time tsetup 100 - - ns ?frame? hold time thold 100 - - ns ?load? pulse width twc 125 - - ns cp l oa d frame tw tw tw tf tr 0.8vdd tdsu u tdhd tl su tl c twc tr tf ts etup thol d d0~d3 0.8vdd 0.8vdd 0.8vdd 0.2vdd 0.2vdd 0.8vdd 0.2vdd 0.8vdd 0.2vdd 0.2vdd 0.8vdd 0.8vdd 0.2vdd 0.8vdd 0.8vdd kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2708-sp10q002-t-1 page 8-2/3 sh. no.
8.3 timing of power supply and interface signal the missing pixels may occur when the lcm is driven except above power interface timing sequence. 8.4 power supply for lcm c :3.3 m f(aluminum electrolytic capacitor) vr :10~20k w tr :2sa673apkc(hfe=100,ic=500ma)or equivalent tr. 4 .7 5v vdd s igna l vee disp of f gnd 5v gnd gnd gnd powe r on powe r o ff 200 ms max 4 .7 5v gnd gnd gnd vdd s igna l vee disp of f gnd valid data 0 min. 0 min. 0 min. 0 min. 200 ms max lcm vd d tr +5v -22.0v c vr vss vee kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2708-sp10q002-t-1 page 8-3/3 sh. no.
9-1/3 kaohsiung hitachi electronics co.,ltd. page 9. dimensional outline 9.1 dimensional outline no. sh. date 3.5 80 120 13.5 3.5 2.5 2.5 4 1 (7) (9) (10) (7) (7) 17.3 (7) (7) 1 12 0.015 0.335 0.015 0.335 7.0max. 12.4 62 60.0 min (59.1) 88.1 min (1.0) (1.5) (1.0) (1.5) 2.01 2.06 (1.5) (1.5) view direction dot area window of backlight effective viewing area window of bezel 90.1+/-0.3 83.985+/-0.1 63+/-0.3 i/f 1 : gmolex 52103-1217 113+/-0.3 73+/-0.3 62+/-0.3 55.985+/-0.1 i/f 2:gmitsumi-m63m83-04 (87.1) 4- f 3.5+/-0.3 (95) unit : mm scale : nts tolerance not specified : +/-0.5mm reference mark : ( ) 7b63ps 2709-sp10q002-t-1 may.20.'99
9.2 display pattern s ca le :nt s uni t :mm measu re me nt tole ra nce :+/-0.1 83.985(240 d ot s) 0.335 0.35 0 .3 3 5 0 .3 5 5 5 . 9 8 5 ( 1 6 0 d ot s ) kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2709-sp10q002-t-1 page 9-2/3 sh. no.
9.3 internal pin connection i/ f1 :molex/52103-1217 (suitable fpc :1.0 pitch,12 pin,0.3 t ) interface pin no. signal level function 1 frame h first line marker 2 load h ? l data latch 3 cp h ? l data shift 4 vdd - power supply for logic 5 vss - gnd lcm i/f1 6 vee - power supply for lc 7 d0 8 d1 9 d2 h/l display data 10 d3 11 disp off h/l h:on/l:off 12 gnd - frame gnd interface pin no. signal level function 1 h.v - cfl supply for cfl cfl 2 n.c - - i/f2 3 n.c - - lcm 4 gnd - cfl gnd cfl i/f2 : mitsumi/m63m83-04 suitable connector: mitsumi m61m73-04 mitsumi m60-04-30-1149(straight) mitsumi m60-04-30-1349(angle) kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2709-sp10q002-t-1 page 9-3/3 sh. no.
10. appearance standard 10.1 appearance inspection condition visual inspection should be done under the following condition. (1 ) in the dark room (2 ) with cfl panel lighted with prescribed inverter circuit. (3 ) with eyes 25cm distand from lcm (4 ) viewing angle within 45 degrees from the vertical line to the center of lcd 10.2 definition of each zone a zone : effective viewing area (refer to our drawing) b zone : except a zone effective viewing area a zone b zone b zone b zo n e b zo n e a zo n e kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2710-sp10q002-t-1 page 10-1/3 sh. no. lcd bezel 45 45 eye eye
10.3 appearance specification *) if the problem occures, about this item the responsible person of both party (customer and hitachi) will discuss more detail. no. item criteria a b scratches distinguished one is not acceptable (to be judge by hitachi limit sample) * - dent same as above * - wrinkles in polarizer same as above * - bubbles average diameter d(mm) maximum number acceptable l d<=0.2 ignore o - 0.2 no. item criteria a b average diameter d(mm) contrast maximum number acceptable distance d<0.25 ignore - 0.25 11. precaution in design 11.1 mounting method since the module is so constructed as to be fixed by utilizing fitting holes in the printed circuit board as shown below, it is necessary to take consideration the following items on attachment to a frame. (1 ) use of protective plate, made of an acrylic plate, etc, in order to protect a polarizer and lc cell. (2 ) to prevent the module cover from being pressed, the spacers between the module and the fitting plates shoud be longer than 0.5mm. (3 ) we recommend you to use protective spacer as figure for protecting lcd module from any kind of shock to your set. 11.2 lc driving voltage(vee) and viewing angle range. setting vee out of the recommended condition will be a cause for a change of viewing angle range. 113.0+/-0.3 73.0+/-0.3 63.0+/-0.3 65.5+/-0.3 spacer 4- f 7.0 protective spacer 4- f 5.0 location of spacers example of mounting protective plate the module spacer spacer customer? s hous protective spacer kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2711-sp10q002-t-1 page 11-1/4 sh. no.
11.3 caution against static charge as this module is provided with c-mos lsi, the care to take such a precaution as to grounding the operator ? s body is required when handling it. 11.4 power on sequence input signals should not be applied to lcd module before power supply voltage is applied and reaches to specified voltage (5+/-0.25v ) if above sequence is not kept, c-mos lsi of lcd modules may be damaged due to latch up problem. 11.5 packaging (1 ) no. leaving products is preferable in the place of high humidity for a long period of time. for their storage in the place where temperature is 35 c or higher, special care to prevent them from high humidity is required. a combination of high temperature and high humidity may cause them polarization degradation as well as bubble generation and polarizer peel- off. please keep the temperature and humidity within the specified range for use and storing. (2 ) since upper polarizers and lower aluminum plates tend to be easily damaged, they should be handled with full care so as not to get them touched, pushed or rubbed by a piece of glass. tweezers and anything else which are harder than a pencil lead 3h. (3 ) as the adhesives used for adhering upper/lower polarizes and aluminum plates are made of organic substances which will be deteriorated by a chemical reaction with such chemicals as acetone, tuluene ethanole and isopropylalcohil. the following solvents are recommended for use: normal hexane please contact us when it is necessary for you to use chemicals other than the above. (4 ) lightly wipe to clean the dirty surface with absorbent cotton waste or other soft material like chamois, soaked in the chemicals recommended without scrubbing it hardly. to prevent the display surface from damage and keep the appearance in good state, it is sufficient, in general, to wipe it with absorbent cotton. (5 ) immediately wipe off saliva off saliva or water drop attached on the display area because its long period adherence may cause deformation or faded color on the spot. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2711-sp10q002-t-1 page 11-2/4 sh. no.
(6 ) fogy dew deposited on the surface and contact terminals due to coldness will be cause for polarizer damage, stain and dirt on product. when necessary to take out the products from some place at low temperature for test, etc. it is required them to be warmed up in a container once at the temperature higher than that of room. (7 ) touching the display area and contact terminals with bare hands and contaminating them are prohibited, because the stain on the display area and poor insulation between terminals are often caused by being touched by bare hands. (there are some cosmetics detrimental to polarizers.) (8 ) in general the quality of glass is fragile so that it tends to be cracked or chipped in handling,specially on its periphery down , ect. 11.6 caution for operation (1 ) it is an indispensable condition to drive lcd? s within the specified voltage limit since the higher voltage than the limit causes the shorter lcd life.an electrochemical reaction due to direct current causes lcd? s undesirable deterioration, so that the use of direct current driver should be avoided. (2 ) response time will be extremely delayed at lower temperature than the operating temperature range and on the other hand at higher temperature lcd? s show dark blue color in hem. however those phenomena do not mean malfunction or out of order with lcd? s which will come back in the specified operating temper ature range. (3 ) if the display area is pushed hard during operation,some font will be abnormally displayed but it resumes normal condition after turning off once. (4 ) a slight dew depositing on terminals is a cause for electrochemical reaction resulting in terminal oper circuit. usage under the relative condition of 40 c 50%rh less is required. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2711-sp10q002-t-1 page 11-3/4 sh. no.
11.7 storage in case of storing for a long period time (for instance, years) for the purpose of replacement use,the following ways are recommended. (1 ) storage in a polyethylene bag with the opening sealed so as not to enter fresh air outside in it,and with no desiccant. (2 ) placing in a dark place where neither exposure to direct sunlight nor light is, keeping temperature in the range for 0 c to 35 c. (3 ) storing with no touch on polarizer surface by anything else. (it is recommended to store them as they have been contained in the inner container at the time of delivery for us.) 11.8 safety (1 ) it is recommendable to crash damaged or unnecessary lcd?s into pieces and wash off liquid crystal by either of solvents such as acetone and ethanol, which shoud up later. (2 ) when any liquid leaked out of a damaged glass cell in contact with your hands, please wash it off well with soap and water. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2711-sp10q002-t-1 page 11-4/4 sh. no.
12. designation of lot mark lot mark lot mark is consisted of 4 digit number. note 1 some products have alphabet at the end or the first. location of lot mark : on the back side of lcm t:made in taiwan. 9 0 5 3 t year figure in lot mark 1999 9 2000 0 2001 1 2002 2 2003 3 month figure in lot mark month figure in lot mark jan. 01 july. 07 feb. 02 aug. 08 mar. 03 sept. 09 apr. 04 oct. 10 may. 05 nov. 11 june. 06 dec. 12 week (day in calendar figure in lot mark 1~7 1 8~14 2 15~21 3 22~29 4 30~31 5 t 3 5 0 9 year month week kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2712-sp10q002-t-1 page 12-1/1 sh. no.
13. precaution for use (1 ) a limit sample should be provided by the both parties on an occasion when the both parties agreed its necessity. judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties. (2 ) on the following occasion, the handling of the problem should be decided through discussion and agreement between responsible persons of the both parties. (1 ) when a question is arisen in the specifications. (2 ) when a new problem is arisen which is not specified in this specifications. (3 ) when an inspection specifications change or operating condition change in customer is reported to hitachi, and some problem is arisen in this specification due to the change. (4 ) when a new problem is arisen at the customer ? s operating set for sample evaluation in the customer site. the precaution that should be observed when handling lcm have been explaind above. if any points are unclear of if you have any requests,please contact hitachi. kaohsiung hitachi electronics co.,ltd. date may.20. ? 99 7b64ps 2713-sp10q002-t-1 page 13-1/1 sh. no.

▲Up To Search▲

Price & Availability of SP10Q002T

	To Download SP10Q002T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .